Concrete towers, glass curtain walls, and below-grade parking keep first responder radios from working inside many Miami buildings. We survey, design, install, and recertify BDA and emergency responder radio coverage systems (ERRCS) so your building passes inspection and firefighters can communicate on every floor.
A compliant system is more than an amplifier in a closet. Here’s everything we handle on a Miami BDA project.
We design and install the complete BDA system, from the signal booster to every indoor antenna, sized for your building’s height, construction, and coverage needs.
Every project starts with a signal strength survey. We measure the incoming signal at the donor antenna location and grid-test each floor to find exactly where coverage fails.
A distributed antenna system carries the amplified signal through floors, stairwells, elevator shafts, and garages so responders have coverage everywhere they need it.
Florida requires BDA trouble conditions to report to the fire alarm panel. We wire supervisory signals for power loss, antenna faults, and battery problems.
We size and install backup power to keep the system running for the required duration during an outage, then load-test the batteries every year.
Annual testing and recertification keeps your certificate of compliance current. We recertify systems we installed and systems we didn’t.
Received a notice that your Miami building needs radio coverage? Start with a signal strength survey.
Miami’s building stock makes in-building radio coverage harder than in most cities. These are the issues we see most.
Towers in Brickell, Downtown, and Edgewater use thick concrete, steel, and low-E glass that block radio signals. Upper floors may have strong outside signal while interior cores and stairwells have none.
Underground and multi-level garages are among the worst coverage areas in any building, and responders often stage there. Garage coverage is a common reason buildings fail a survey.
Florida requires existing high-rise buildings to provide in-building emergency responder radio coverage, and many Miami towers built before the requirement are now being retrofitted while occupied.
A poorly designed BDA can interfere with neighboring buildings or the public safety network itself. Proper design and gain settings prevent that.
Many older BDA installs were never tied into the fire alarm panel for supervisory monitoring, which leaves the building out of compliance even if radios work.
Donor antennas and rooftop mounts in Miami-Dade must withstand High-Velocity Hurricane Zone wind loads. Mounting and cable routing need to be designed for it.
Is your BDA recertification overdue? We will test it and get your certificate current.
We survey and install BDA systems in towers, garages, hospitals, and large buildings throughout the City of Miami.
Also need fire alarm work? See our Miami fire alarm company page. We design and certify BDA systems across all of Miami-Dade County.
From the first survey to the certificate on file, here’s how we deliver a compliant system.
We measure the donor signal at the roof and grid-test every floor, stairwell, elevator, and garage level to see exactly where coverage fails.
We design the BDA and antenna layout, coordinate with City of Miami Fire-Rescue and the public safety radio system operator, and pull the permits.
We install the amplifier, donor antenna, and indoor antennas, connect backup power, and wire supervisory signals to the fire alarm panel.
We complete acceptance testing, deliver your documentation, and keep you on an annual recertification schedule.
BDA work sits between radio engineering and fire alarm compliance. We handle both, so nothing falls through the gap.
We survey and install systems in occupied towers across Brickell and Downtown, working around residents and tenants.
We install the BDA and make the fire alarm supervisory connection ourselves, so there’s no finger-pointing between two contractors at acceptance testing.
Our technicians hold NICET certification in fire alarm systems, which matters because BDA supervision is inspected as part of fire alarm compliance.
We hold Florida licenses EC-13010477 and EF-20001077 and use FCC-registered public safety signal boosters on every installation.
Clients on our annual program get scheduled before their certificate expires, so the due date never sneaks up on management.
What Miami property managers, boards, and building owners ask us most about in-building radio coverage.
It depends on the building’s height, size, construction, and below-grade areas, and on what the fire department requires. Many high-rises and large buildings do. A signal strength survey tells you whether your building already meets minimum coverage or needs a system.
ERRCS, or emergency responder radio coverage system, is the overall system that provides in-building coverage. The BDA, or bi-directional amplifier, is the main piece of equipment in it. Inspectors and contractors often use the terms interchangeably.
We measure the public safety signal at the roof, then take readings on a grid across every floor, stairwell, elevator, and garage level. The result shows exactly where coverage passes and where it fails.
Smaller buildings can take a few days. Large towers with many floors and garage levels can take several weeks. Permitting and coordination with the radio system operator add time, so starting early matters.
Yes. Florida requires the system to report supervisory conditions like power loss, signal loss, and battery trouble to the fire alarm panel. We handle that connection as part of every installation.
Annually. The system has to be tested and a new certificate of compliance issued each year. We track the due date and schedule it for you.
Whether you’ve received a notice, are planning new construction, or need an existing system recertified, tell us about your building and we’ll start with a survey.